Skip to content

Levels

Levels are the heights a scene can be stood on: the floors of a house, decks up in the trees, the walk along the top of a city wall. A scene describes them in feet, and the Levels panel names them, joins them with stairs and ladders, and sets how the depths below look.

This page covers how a scene’s levels are described. How they play:

Only GMs can edit levels, and, like the other building tools, only on a computer or tablet.

A token has an elevation: the height it stands at. A wall, a light or an overlay tile can carry a span of heights — a bottom and a top. Leave the bottom empty and it reaches down past everything; leave the top empty for “and up”. Leave both empty and it stands across every height, as everything did before levels, so an older map doesn’t change.

On a… The span means Where to set it
Wall The heights it blocks. A wall from 0 to 10 ft is a ground-floor wall. Wall Tool → Edit or Multi → select walls → Heights
Light It stands at the bottom and lights every level up to the top. Lighting Tools → select a light → Geometry tab → Heights
Overlay tile Floor at: the floor it shows. Seen up to: the highest a viewer can stand and still see it. Overlay Tiles → select a tile → Level

Above the fields, Level picks a named level for you: on a wall or a light it fills in that level’s heights, on a tile its floor. Every height clears them; anything you type yourself reads as Custom.

Building on a level. When you see the map from a level you’ve picked (the Seeing from button beside the minimap), new walls, lights and tiles go on that level, and each tool’s panel says so. Choose Every height there to draw them across every height instead.

With several walls selected that disagree, the fields say Mixed, and what you type applies to all of them. A tile’s Above a viewer setting says how it’s drawn for someone below it: Hide (an upper storey), Fade (a deck overhead) or Soft reveal (a roof or canopy, opened round the tokens under it). A storey wall or tile from an older battle map reads as its storey — 10 ft a storey — until you give it a span.

  1. At the Build table on a computer, open the Table panel’s Scene pane and click Levels beside its Levels heading (or Draw a region under the level list, once the scene has levels).
  2. The Levels panel appears with three sections: Levels, Ways between levels and Depth look.

A named level is a label on a band of heights — “Ground”, “The loft” from 10 ft, “Upper decks” from 40 ft and up — so the map reads “Upper decks” instead of “43 ft”. Names never change a rule; the heights do that.

  • No names yet? The panel shows, greyed out, the bands the map’s tiles already make. Name these copies them in for you to rename.
  • Each level has a name, a from height and a to height in feet; leave to empty for “and up”.
  • Add level starts a new band above the highest one, closing the old top band where the new one starts.
  • A band whose top isn’t above its bottom, or that overlaps another, gets a warning underneath. Keep typing — it goes when the numbers make sense.

A way joins two heights at one place — stairs, a ladder, a rope, a spiral stair, a ramp, a bridge, or a hole to drop through — and works in both directions.

  1. Click Place a way up, then click the map where it stands. Esc or a right-click stops placing; dragging still pans the map.
  2. The new way joins the level you’re seeing from to the next one up, as a ladder that asks. Change any of it in its row.
  3. To move it, drag it on the map. To make it bigger or smaller, drag the handle on its edge.

Each row has its kind; Auto or Ask (Auto: a token that ends its move there changes level at once; Ask: it’s offered the climb); the two heights it joins; and an optional label, such as “Trapdoor”. The crosshair pans the map to it. While the panel is open, every way is drawn on the map, and the one you placed or showed last is picked out. A way whose two ends aren’t the floors of named levels gets a warning underneath: a token taking it would end up in the air.

Undo. The arrow in the panel’s title, or Ctrl/⌘ Z while the panel is open, undoes the last change. Deleting a level or a way also shows a note with Undo, which puts that one back.

How what lies below the level you’re on is drawn: softened, darkened and hazed by how far down it is — the forest floor seen from the canopy, the street from the battlements.

  • Blur — how soft the depths get.
  • Dim — how much of their light is kept: ×1 leaves them as bright.
  • Haze and Haze colour — how far they’re mixed toward a colour, such as pale sky or a drawn map’s paper.
  • None turns it off; Add a depth look turns it back on.

A battle map from the Map Foundry fills all of this in: each floor’s tiles with their heights and floor outlines, every storey’s walls and lights, the stairs and ladders between them, and a depth look to suit the map — a treetops map as one scene with all its levels (made with Create scene, or brought in with Import Scene from its zip). A town’s battle map made with Raised floors brings its wall-walks, towers, stone bridges, lofts, galleries and rafters as levels, named after what stands there (Wall-walk, Tower tops, Bridges, Rafters); see Walls, towers and bridges to stand on. Open Levels to see what it made and rename or adjust any of it.

A building or dungeon exported as a picture for each floor — from Dungeondraft, Dungeon Alchemist, Inkarnate or drawn by hand — or as a UVTT file for each floor becomes one scene with levels through Import Scene → Build from floors; see Building levels from floor images.