Measuring distance
The ruler answers “can I reach them?” without anyone counting squares out loud. Players, GMs and observers can all use it.
Drawing a ruler
Section titled “Drawing a ruler”- Pick Measure Mode on the dock across the top of the table, or press M.
- Click where you want to measure from. If you click on a token, the ruler snaps to that token’s centre.
- Move your cursor — the line follows it and the distance updates live.
- Click again to lock the ruler in place.
- Click a third time to start a fresh measurement, or press Escape to clear it.
The total sits in a label just past the end of the arrow. Small ticks along the line mark each grid square, with every fifth tick longer, so you can count at a glance. The ruler stays the same size on screen however far you zoom in or out.
Measuring around corners
Section titled “Measuring around corners”A path to a door or around a pillar isn’t a straight line. Add waypoints as you go:
- Shift-click drops a waypoint where the cursor is, and the ruler carries on from there.
- Right-click or Backspace takes back the last waypoint. With none left, it clears the ruler.
- A plain click finishes the ruler, as before.
Each leg gets its own small label, and the main label shows the whole path. If your game counts every second diagonal as double (Pathfinder and Starfinder’s 5-10-5), the count carries on across waypoints — it doesn’t restart because the path turned a corner.
Measuring between levels
Section titled “Measuring between levels”In a scene with levels, an end of the ruler on a token measures from that token’s height, and one on open ground from the floor on the level you’re seeing from. When the two ends are at different heights, the label adds the climb — 35 ft · 15 ft up — and the total counts it. See Areas, measuring and senses across levels.
Showing the table your ruler
Section titled “Showing the table your ruler”While you measure, everyone else at the table sees your ruler in your cursor colour, with your name on its label. It disappears for them when you clear it or put the tool down.
Players share their ruler by default. GMs don’t, because a GM measuring from a hidden monster would show the table where it is. Either of you can change that with Show my ruler to the table in Tabletop settings.
Someone else’s ruler reads in their units, so “25 ft” means the same thing on every screen.
Difficult ground and your game’s rules
Section titled “Difficult ground and your game’s rules”When the ruler crosses difficult terrain, a second line under the total says what the path really costs to walk — for example 45 ft through difficult ground — or Path blocked if it crosses impassable ground. If the GM has hidden the terrain overlay, players still see the true cost, just not why.
With a token selected, the ruler counts the way that token’s game system does. Pathfinder and Starfinder count every second diagonal as 10 feet, and their difficult ground adds 5 feet a square, rather than doubling the step as D&D does.
The four unit modes
Section titled “The four unit modes”Open Settings (the gear at the top right) and find the Measurement section. The Units picker changes how the ruler counts:
| Units | The label reads |
|---|---|
| Grid squares | The distance in whole squares, e.g. 4 squares. |
| D&D, 5 ft per square | The distance in feet, e.g. 20 ft. |
| Daggerheart ranges | A range band name. The line itself is coloured by band — green through Melee, blue through Very Close, and so on — with a notch and a label where each band ends. |
| Daggerheart range rings | The same band names, drawn as coloured rings spreading out from the starting point. The band you end in is the brightest. |
This is a personal setting — changing it doesn’t change what anyone else’s ruler shows.
The Daggerheart bands
Section titled “The Daggerheart bands”Both Daggerheart modes use the same five bands, measured out from the starting point:
| Band | Reaches out to |
|---|---|
| Melee | 1 square |
| Very Close | 3 squares |
| Close | 6 squares |
| Far | 12 squares |
| Very Far | beyond 12 squares |
In Range Rings mode each band gets its own colour, so a single click near a creature shows the whole envelope at once — handy when the whole table needs to agree on who’s in Close range.
Range is a straight line from one point, so the band marks and rings are drawn only while the ruler has no waypoints. With waypoints, the label names the band of the whole path’s length.
Related
Section titled “Related”- Keyboard shortcuts — M for the ruler, and the rest.
- Tabletop settings — the Units picker and Show my ruler to the table.
- Difficult terrain — what makes a path cost more.
- Targeting — area shapes that actually select targets.
- The grid — square size is what the ruler counts.